A broadband filter with two transmission zeros adopting a new design method

A new design method was proposed in this article to insert transmission zeros in the broadband filters. In this method, the coupling line was connected to a certain position on the resonator. And then the coupling strength was adjusted by the connecting position. The open end of the resonator was hung and then the cross‐coupling was introduced to realize transmission zeros. This coupling method could add an adjustable parameter to improve the freedom of design and convenient to insert the transmission zeros. To verify this method, a highly selective coupled‐line microstrip filter with two transmission zeros was designed, fabricated, and measured. The measured results were in good agreement with the simulated ones. The return and insertion losses of the broadband filter were better than 18 and 2 dB, respectively. The relative bandwidth of the filter (FBW) was more than 68%. The rectangular coefficient (30 dB:1 dB) was less than 1.21.     

纵轴式掘进机截割头载荷影响因素的仿真分析

针对现有掘进机截割头载荷特性研究方法采用单一影响因素不能全面反映截割头载荷及其波动变化规律的问题,通过分析截割头瞬时载荷,确定了纵轴式掘进机在水平截割工况下截割头载荷的主要影响因素有截割岩石特性、截割头掏槽深度、截割头吃刀深度、截割头转速和截割臂摆速。针对某纵轴式掘进机水平截割工况,采用Matlab对影响截割头载荷的多种因素进行仿真分析,得到了各向载荷及其波动随各因素的变化规律:截割头载荷随着岩壁普氏系数的增大而增加,其中横向阻力增加尤为明显,横向阻力波动程度高于其他方向载荷,且随着岩壁普氏系数的增大呈减小趋势;随着截割头掏槽深度的增加,截割头各向载荷近似呈线性增加,其中升力增加幅度最大,各向载荷波动则随着截割头掏槽深度的增大而减小;随着吃刀深度的增加,截割头载荷总体呈增大趋势,载荷波动程度则随之减小;在截割头转速一定的情况下,截割头载荷均随着截割臂摆速的增加而增大,在同一摆速下,截割头载荷随着截割头转速的减小而增大,横向阻力波动明显高于升力和推进阻力波动,横向阻力和推进阻力波动按截割头载荷规律变化,升力波动则与之相反。截割头载荷波动变化规律与截割头载荷变化规律不尽一致,有时甚至相互冲突。因此,掘进机作业过程中应合理选择截割头掏槽深度、吃刀深度等操作参数和截割头转速、截割臂摆速等运动参数,使各参数相互匹配,以减小掘进机振动,延长使用寿命。     

一种压电半导体纳米线的热电耦合性能研究

采用有限元分析方法,研究了一种n型压电半导体纳米线(氧化锌)的电热耦合性能,分析了外部温度对氧化锌纳米线内部机械场、电场及电流场分布的影响,并讨论了本构方程线性化对电学参数的影响。研究结果表明,温度对氧化锌纳米线的电场、载流子浓度和电流密度影响很大,采用线性本构和非线性本构求得的电场、电子浓度和电流密度最大相差分别为24%,32%和68%,基于非线性本构分析压电半导体的电学性能会引起很大误差。该研究结果可为压电半导体器件利用温度调控电场、电流提供理论依据。     

Improved one-dimensional beam model for unbalanced composite single-lap joint

An analytical nonlinear solution was provided for unbalanced composite single-lap joint (CSLJ) using an improved one-dimensional beam model, which incorporated the effect of bending–tension coupling. The bending–tension coupling stiffness was introduced to characterize the coupling bending and tension behavior induced by the un-symmetric stacking sequence of composite laminates. The governing differential equations captured the bending–tension coupling behavior and the geometrically nonlinear features were constructed based on the displacement compatibility conditions of flexible interface. The transverse deformation in overlap region, edge moment factors and adhesive stress distributions for the unbalanced CSLJ with inflexible, intermediate flexibility and flexible adhesive can be determined by the present one-dimensional beam model. The accuracy of the present model was validated by the comparison with nonlinear finite element model. The effect of bending–tension coupling on edge moment factors and peak values of adhesive stresses was shed light on with the present model.     

A comparative study for consistency-based decision making with interval multiplicative preference relations

ABSTRACT

To ensure the reasonable application and perfect the theory of decision making with interval multiplicative preference relations (IMPRs), this paper continues to discuss decision making with IMPRs. After reviewing previous consistency concepts for IMPRs, we find that Krej?í’s consistency concept is more flexible and natural than others. However, it is insufficient to address IMPRs only using this concept. Considering this fact, this paper researches inconsistent and incomplete IMPRs that are usually encountered. First, programming models for addressing inconsistent and incomplete IMPRs are constructed. Then, this paper studies the consensus of individual IMPRs and defines a consensus index using the defined correlation coefficient. When the consensus requirement does not satisfy requirement, a programming model for improving consensus level is built, which can ensure the consistency. Subsequently, a procedure for group decision making with IMPRs is offered, and associated examples are provided to specifically show the application of main theoretical results.     

天然橡胶/顺丁橡胶/丁苯橡胶自润滑喷蜡橡胶材料的性能

在天然橡胶(NR)/顺丁橡胶(BR)/丁苯橡胶(SBR)为基体的自润滑喷蜡橡胶材料中加入芥酸酰胺,考察芥酸酰胺作为润滑剂时对NR/BR/SBR自润滑喷蜡橡胶材料的硫化特性、力学性能、门尼黏度、摩擦系数及耐老化性能的影响。结果表明,与未加芥酸酰胺的胶料相比,当芥酸酰胺用量为10份时,胶料转矩减小,焦烧时间和正硫化时间缩短,扯断伸长率从388%增加至523%,拉伸强度降低了21.36%,邵尔A硬度、压缩永久变形分别下降5.56%和8.74%,动、静摩擦系数分别减小23.46%和24.82%,门尼黏度降低20.89%,耐热氧老化性能下降。硫化胶拉伸100%停放5 min后,表面出现明显的白色润滑膜,胶料流动性变好,各组分分散得更均匀,断面更光滑。     

超精密气体静压系统节流器法向随机微振动研究

以无气腔平面节流器为研究对象,对节流器流固耦合法向随机微振动进行了理论仿真和实验研究。受限于节流器厚度与气膜厚度尺寸的差异和输入初始边界条件,建立了节流器的COMSOL仿真简化模型,对节流器-气膜微流场进行双向流固耦合数值模拟。仿真结果表明,节流器的法向随机微振动幅值关于节流器中心对称,且由中心向边缘逐渐增大;微振动幅值随气体入口流速的增大而增大。实验采用纳米级激光测振仪,依次测量供气压力为0.1,0.2,…,0.5 MPa时尺寸为75 mm×50 mm×14 mm的HEXAGON双环联结型节流器多个不同位置的法向振动,实验结果表明,法向随机微振动幅值分布特性与仿真结果一致,关于节流器中心对称,且由中心向边缘逐渐增大,验证了节流器法向微振动的"跷跷板"振动形式;在0.5 MPa供气压力下,边缘振动幅值超过1 nm。对实验数据进行功率谱密度分析,结果表明不同供气压力下法向随机微振动均在9.4 kHz和10.6 kHz处产生较大功率,可认为与节流器-气膜流固耦合系统的固有频率有关。研究结果有效地揭示了节流器法向随机微振动的特性,为气体静压系统避开随机共振区、优化气体静压系统的设计提供了理论指导。     

An up to date review of continuously variable speed wind turbines with mechatronic variable transmissions

As a promising and potential alternative to conventional fixed or variable speed wind turbines, continuously variable speed wind turbines (CVSWTs) with variable transmissions offer improved power efficiency and enhanced power control capabilities. The CVSWTs can be generally achieved by adapting mechatronic variable transmissions in the turbine drive train for continuously variable speed operations for wind turbines. Therefore, this paper serves to provide an up to date and exhaustive review of the CVSWTs with mechatronic variable transmissions such as mechanical variable transmission, electrical variable transmission, and power splitting transmission. In this paper, the analysis of CVSWTs with different mechatronic transmission topologies is performed regarding basic configurations, dynamic characteristics, control principles, and experimental or simulation results. Review results indicate the feasibility of applying CVSWTs with such mechatronic transmissions and highlight superiorities of the CVSWTs with power splitting transmission. The CVSWT with power splitting transmission will be particularly suitable for megawatt‐scale turbine systems and will hence increase the economic competitiveness of these turbines due to its large power capacity and high reliability. The directions or challenges for future investigations of CVSWTs with such mechatronic transmissions are also presented to foster in‐depth understanding of such CVSWTs and their control strategies.     

宁夏红寺堡盆地隐伏古隆起成因机制及其对区域沙漠化的影响

目前对于青藏高原东北缘活动构造研究多集中于活动断裂带的活动性,而对夹持于其间的沉积盆地构造格架及活动性研究甚少。以夹持于烟筒山断裂与牛首山—罗山断裂之间的宁夏红寺堡盆地为研究对象,采用重力资料重处理解译、音频大地电磁测深(AMT)和地震勘探相结合,揭示红寺堡盆地隐伏构造特征,并进一步采用盆山一体化思路分析隐伏构造的成因机制及其对区域沙漠化的控制作用。结果表明:青藏高原在中新世末发生强烈的NE向推挤、扩展和隆升,红寺堡盆地由坳陷盆地转变为挠曲盆地; 在青藏高原NE向扩展的影响下,烟筒山断裂发生强烈的逆冲作用,古生代—中生代基底逆冲于古近系—新近系之上,受构造变形影响的最新地层为中新统彰恩堡组; 红寺堡盆地内的隐伏古隆起呈NW—SE向,与烟筒山构造带具有相同的构造动力学背景,受青藏高原NE向扩展影响形成于中新世末,并且至今仍具有活动性; 隐伏古隆起周缘断裂的活动破坏了地表稳定性、蓄水能力和地表植被,导致区域沙漠化呈现有规律的NW—SE向带状展布。该研究成果对于宁夏红寺堡盆地区域稳定性评价及沙漠化的综合治理具有现实指导意义。     

提升生活排水系统卫生安全性能的关键问题

新冠肺炎确诊患者粪便病毒检测呈阳性,意味着新冠病毒可能会通过气溶胶的方式进行传播,使得生活排水系统的卫生安全问题时隔17年后再次摆在人们面前。以保障人的健康为出发点,从基础研究、排水机理、系统设计、施工监管、维护管理等多方面提出了提升生活排水系统卫生安全性能的关键问题,以期从全生命周期内切断排水系统可能传播病毒的隐形途径,切实保障居民居家健康。